Note: any 80-96 F150 or Bronco to be lifted 1.5-2" will have alignment problems unless the factory shims are at or near zero degrees. Verify what's on your truck prior to purchase. Otherwise, a minimum of 4" of lift will be required in order to achieve correct alignment. No lift will be achieved on vehicles with big block engines.

The difference between a Superlift Standard lift kit and a Superunner lift follows. Standard kits utilize longer radius arm brackets that replace the stock pieces. The Superunner series replacement radius arms are considerably longer than stock offering caster correction and additional benefits.

Using the Superunner Steering Linkage in addition to the pitman arm lowers the pivot point of the tie rods close to the axle halves’ pivot point and allows the use of new tie rods that are proportional in length to the axle halves. The result is steering linkage that is in almost perfect phase with the suspension, yielding optimum steering response. 

TruSpeed Speed Sensor

Super-Trac traction bars

Brake Lines

1-2" kit includes front coils and adjustable alignment bushings. Your vehicle must have near zero degree factory shims to achieve for proper alignment.

4" & 6" lifts include front coils, all drop bracketry, rear blocks or leaf springs, and pitman arm for power steering. 6" additionally includes sway bar brackets. Extended brake lines are strongly recommended for 4" lift and required for 6" lift.

 Kits use rear blocks and/or add-a-leafs and Systems use rear leaf springs.

Link to Superlift Photos

Standard components

• Axle pivot brackets include camber adjustment bolts for precise alignment

• Coil springs give comfortable ride, yet durable enough for off-road

• Allows use of 33" tires

• Shocks & pitman arm purchased separately

Performance components

• Includes new extended radius arms

• Gives better articulation, more ground clearance & sharper turning radius

• New radius arms are 15" longer than stock for more wheel travel

• Angled inward to allow better tire clearance 

• Rear mounting brackets use a pivoting axis mount to improve articulation

• Shocks & pitman arm purchased separately

The Skyjacker 2" lift kit includes front coils and rear add-a-leafs. For the 2" lift the factory shims must be near zero degrees to achieve alignment. Over-sized caster camber shims are required.

The 4" & 6" Class I lift kits include coils and all drop bracketry. Kits use rear blocks and/or add-a-leafs and Systems use rear leaf springs. For the 4" systems with rear leaf springs, the factory block is removed.

The Class II kits and systems are available for 4" and 6" lifts and include a pitman arm & replacement tubular offset radius arms extended 15" longer than stock offering up to 30% more wheel articulation and less frame fatigue than using radius drop brackets. Newly designed center hinge brackets are both stylish and more rugged than stock or standard applications.

Skyjacker lifts available in black only.

Multiple shock mounts

8" lifts include front coils, all drop bracketry or longer radius arms, rear blocks or leaf springs, pitman arm, stainless steel braided brake lines and frame support bar.

Brake Lines recommended for 4" lift and required for 6" lifts. 

Kits use rear blocks and/or add-a-leafs and Systems use rear leaf springs.

Price

Price

• Designed to improve ride quality and vehicle control both on- and off-road 
• Features Rancho's unique, patented Extended Radius Arm Design
• New front suspension components significantly increase wheel travel envelope, and reduce undesirable geometry changes

Rancho lift kits available in black only.

Performance System components

• Sport Systems: include pivot brackets, dropped pitman arm, rear blocks, plus all mounting hardware and installation instructions 
• Performance Systems: include pivot brackets, dropped pitman arm, rear Add-A-Leaf springs, radius arms for enhanced steering angle, plus all mounting hardware and installation instructions

81-96 4WD F150 6" Basic Lift
This system uses the factory radius arms with heavy duty drop brackets for an economical lift. I beams are relocated with 1/4" thick bracketry. System also includes coil springs, pitman arm, sway bar brackets, alignment cams and more.

6" Basic -- Fabtech lift kits available in black only.

Allows use of 315/70R17 tires, 17x8 wheels with 4-1/2" BS

Daystar Comfort Ride Suspension kits are the perfect choice for a lift that will not only increase vehicle height, but enhance performance. Improve ground clearance, allow for larger tires, utilize most of the stock components and improve the all around on & off road capabilities at an affordable price.

Available in black only

Lift

Part #